Tools

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base...

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base...

AT-3B Small Black Nylon Wire Tie Mount - Qty. 500The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about...

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40...

AT-5 Large White Nylon Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge...

AT-5B Large Black Nylon Wire Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...

AT-6031 Metal Bond AdhesiveAT-6031 is a 10-to-1 metal bonding adhesive. It has high viscosity (cures in 10–12 minutes), has a 6-minute working time, and develops working strength in 40 minutes. AT-6031 develops more than 2,500 lbs. (psi) of...

AT-651 Mixing Tips for Use with AT-6031 Adhesive - Qty. 10Weld Mount’s AT-651 mixing tip is designed specifically for use with Weld Mount’s AT-6031 adhesive. AT-6031 is a 10 to 1 adhesive that requires a mixing tip with more mixing chambers...

Aluminum Base Wire Tie MountThis tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with the wire harness easier. This tie mount is designed for...

Aluminum Base Wire Tie MountThis tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with the wire harness easier. This tie mount is designed for...

AT-85810 Mixing Tips *10-PackIts unique design eliminates any possibility of the cartridge plugging up as the entry is separated.  This prevents cross-contamination of the two parts, keeping the cartridge ends clean and clear for multiple uses...

Double ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 1" Stud Required:...

Double ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.5" Stud Required:...

Double ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.25" Stud Required:...

Double ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.75" Stud Required:...

Double ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.375" Stud Required:...

Double ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.625" Stud Required:...

Executive Fastener Kit - No AdhesiveThis Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Does NOT Contain Acrylic Adhesive The Weld Mount System Eliminates The...

Industrial Kit with AT-8040 AdhesiveThis Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For Industrial Maintenance Shops. A Wide Selection Of Weld Mount Parts Are Supplied In A Heavy "Durham" Metal Box Which Is A...

Dual Pusher RodThe AT-500 dual pusher rod is used to dispense equal amounts of our AT-2010 or AT-4020 adhesive for manual mixing. This dual pusher rod can not be used with our AT-300 or AT-350 mixing tips as it does not generate enough force to push...

No Slide Metal/Composite Bonder *Case of 10*Revolutionary Metal Bonder will hold heavy parts at application without sliding on a vertical or overhead surface. AT-8040 will hold 3,500 lbs in 40 minutes - no Welding, Drilling, or Tapping.Weld Mount...

Retail Wire Tie Kit with AT-8040 AdhesiveThe AT-1050 kit contains one manual mix tube of AT-8040 adhesive and 25 pieces of AT-5 white wire tie mount. Just enough parts for a small wiring job and an ideal introduction to Weld Mount.AT-1050 Kit...

Single ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 1.0" Stud Required:...

Single ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.5" Stud Required:...

Single ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.250" Stud Required:...

Single ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.75" Stud Required:...

Single ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.375" Stud Required:...

Single ClampEach clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.Features: Hose OD: 0.625" Stud Required:...

Adhesive Mixing Tip For AT-6030Our AT-650 mixing tip is designed specifically for use with our AT-6030 adhesive. AT-6030 is a 10 to 1 adhesive which requires a mixing tip with more mixing chambers to insure proper mixing before use. These mixing tips...

Floating Nut PlatesOur floating nut plate is designed for through-hole mounting applications. The rubber fixture holds the part in the through hole while it is bonded in place with our acrylic adhesive. The fixture keeps the threads clean during bonding...

Floating Nut PlatesOur floating nut plate is designed for through-hole mounting applications. The rubber fixture holds the part in the through hole while it is bonded in place with our acrylic adhesive. The fixture keeps the threads clean during bonding...

Stainless Steel Panel Stud .62" Base 8 x 32 Thread 1.5" Tall - 100 PackWeld Mount offers wire tie mounts, hose, and cable clamps, studs, standoffs, and floating nutplates. All of the fasteners are mounted with our unique non-sag acrylic adhesives which...