C. Sherman Johnson

"Captain Hook" Chain Snubber Large Snubber Hook Only (1/2" T-316 Stainless Steel Stock)The "Captain Hook" Chain Snubber can be used in a few different ways:Use the claw and attached line to relieve...

"Captain Hook" Chain Snubber Large Snubber Hook for 3/8" & 1/2" Chain with 15' of 5/8" 3 Strand NylonThe "Captain Hook" Chain Snubber can be used in a few different ways:Use the claw and...

"Captain Hook" Chain Snubber Small Snubber Hook Only (5/16" T-316 Stainless Steel Stock)The "Captain Hook" Chain Snubber can be used in a few different ways:Use the claw and attached line to relieve...

"Captain Hook" Chain Snubber Small Snubber Hook for 1/4" & 5/16" Chain with 12' of 1/2" 3 Strand NylonThe "Captain Hook" Chain Snubber can be used in a few different ways:Use the claw and...

Spreader Flag Halyard KitIncludes 40ft. of polyester line, block with bail and shroud cleat.

Pulpit Anchor for 1" RailThis fitting can be used on the stern rail and bow pulpit to terminated jaw fittings for lower or upper life lines. (1/2" hole). Hole will not accept cast gate hooks. 

Stanchion Eye for 1" StanchionThis fitting is used on a stanchion for adding lower life lines without the need to drill holes for the cable to pass through. (5/16" hole).

Eye to Deck Toggle FittingThis fitting can be mounted to any flat surface and accept life line fittings, line, etc. Toggling action is 140 degrees. 

Eye to Jaw FittingThis fitting will convert a small bail at the stern rail to the standard gate eye to accept the over center gate hook.

Eye to Eye Adjustable FittingThis fitting can be used wherever an eye is required on each side of the stanchion. Adjustable between 3/4" and 1". 

Short Adjuster for 3/16" WireGenerally used at the stern rail in conjunction with the single gate eye to tension that section of the gate.Specifications:3/16" Wire1/4" Pin1" adj.

Short Adjuster for 1/8" WireGenerally used at the stern rail in conjunction with the single gate eye to tension that section of the gate.Specifications:1/8" Wire1/4" Pin1" adj.

"T" Style Toggle Jaw for 3/16" WireGenerally used at the stern rail when no gate is required with a turnbuckle forward.

"T" Style Toggle Jaw for 1/8" WireGenerally used at the stern rail when no gate is required with a turnbuckle forward.

Deck Toggle "T" Style for 3/16" WireThis fitting can be used wherever a cable needs to be terminated to a deck or bulkhead.

Deck Toggle "T" Style for 1/8" WireThis fitting can be used wherever a cable needs to be terminated to a deck or bulkhead.

Double Threaded Interlocking Gate Eye for 3/16" WireA single eye is used on one end of the gate area and threaded into eye nut.

Double Threaded Interlocking Gate Eye for 1/8" WireA single eye is used on one end of the gate area and threaded into eye nut.

Interlocking Swivel Gate Eye for 3/16" WireAn interlocking gate eye is used at the opposite end of the gate hook as a "hinge" for the gate.

Interlocking Swivel Gate Eye for 1/8" WireAn interlocking gate eye is used at the opposite end of the gate hook as a "hinge" for the gate.

Single Threaded Gate Eye for 3/16" WireA single eye is used on one end of the gate area and threaded into eye nut.

Single Threaded Gate Eye for 1/8" WireA single eye is used on one end of the gate area and threaded into eye nut.

Single Swivel Gate Eye for 3/16" WireA single eye is used on one end of the gate area to attach the gate hook.

Single Swivel Gate Eye for 1/8" WireA single eye is used on one end of the gate area to attach the gate hook.

Deck Toggle Turnbuckle to Hand Crimp Terminal for 3/16" WireThis "T" bolt style fitting is used on decks or bulkheads. T-316 stainlessSpecifications:3/16" Wire1/4"-283" adj.

Deck Toggle Turnbuckle to Hand Crimp Terminal for 1/8" WireThis "T" bolt style fitting is used on decks or bulkheads. T-316 stainlessSpecifications:1/8" Wire1/4"-283" adj.

Closed Body Jaw to Swage Tubular Turnbuckle for 3/16" WireJaw to swage- Check Nut Locking.Specifications:3/16" Wire1/4" Pin3" adj.

Closed Body Jaw to Swage Tubular Turnbuckle for 1/8" WireJaw to swage- Check Nut Locking.Specifications:1/8" Wire1/4" Pin3" adj.

Open Body Jaw to Swage Turnbuckle for 1/8" WireClassic, traditional design. Forged silicon bronze body with T-316 stainless ends.Specifications:1/8" Wire1/4" Pin3" adj.

Open Body Jaw to Swage Turnbuckle for 3/16" WireClassic, traditional design. Forged silicon bronze body with T-316 stainless ends.Specifications:3/16" Wire1/4" Pin3" adj.

Snap Gate Hook - Body Only - 1/4" - 28 Left HandFor those that wish to replace their existing hooks- just match up the thread size. 3-1/2" long from end of body to inside bearing point of hook...

Snap Gate Hook - Body Only - 5/16" - 24 Right HandFor those that wish to replace their existing hooks- just match up the thread size. 3-1/2" long from end of body to inside bearing point of hook...

Snap Gate Hook - Body Only - 5/16" - 24 Left HandFor those that wish to replace their existing hooks- just match up the thread size. 3-1/2" long from end of body to inside bearing point of hook...

Over Center Snap Gate Hook for 3/16" WireThe over center design has no load on the swinging hook when closed. This feature allows easy opening, yet stays secure with a heavy split ring on the...

Over Center Snap Gate Hook for 1/8" WireThe over center design has no load on the swinging hook when closed. This feature allows easy opening, yet stays secure with a heavy split ring on the plunger...

Splice Line Gate Kit - Aft for One SideC. Sherman Johnson Marine's Splice Line fittings allow you to easily splice hi tech Dyneema line to standard life line fittings. The Splice Line fittings are...

Splice Line Gate Kit - Midship for One SideC. Sherman Johnson Marine's Splice Line fittings allow you to easily splice hi tech Dyneema line to standard life line fittings. The Splice Line fittings...

Splice Line Large Boat Kit for Boats up to 40'C. Sherman Johnson Marine's Splice Line fittings allow you to easily splice hi tech Dyneema line to standard life line fittings. The Splice Line...

Splice Line Small Boat Kit for Boats up to 30'C. Sherman Johnson Marine's Splice Line fittings allow you to easily splice hi tech Dyneema line to standard life line fittings. The Splice Line...

Splice Eye with Threaded Stud: 5/16"-24 x 2-1/2" RH with Splice EyeIncludes cross-hole for cotter pin*Dyneema Line not included with fittingsC. Sherman Johnson Marine's Splice Line fittings allow...