Lumishore LUX SL180 CRGBW Strip Light — 300mm

Lumishore strip light

Lumishore LUX SL180 CRGBW Strip Light — 300mm

A factory-sealed, IP68-rated CRGBW LED strip built around 180 LEDs per meter and five independent color channels. This 300mm (12") length delivers approximately 1.5 W of tunable light — from warm white at 2700 K to cool white at 6500 K and the full RGB spectrum. This page keeps the length, wattage, MPN, and driver requirements high on the page so you can confirm the right strip light setup before ordering.

Garmin authorized dealer

What's included

• Lumishore LUX SL180 CRGBW strip light — 300 mm (12") pre-sealed length
• 3M adhesive backing (pre-applied)

Best fit

Best for above-water accent and mood lighting on any vessel where a precise, factory-sealed 300 mm run is needed — under gunwales, cockpit coamings, helm panels, cabin headliners, T-top undersides, and step edges. Ideal for short accent segments such as under navigation light housings, cup-holder channels, or courtesy step edges where the 300 mm pre-sealed length is a natural fit.

Why choose this strip light

• Full-spectrum CRGBW: Five independent LED channels (cold white, red, green, blue, warm white) in a single strip — dial in any color or tune white from 2700 K to 6500 K without swapping fixtures.
• 180 LEDs per meter: High-density layout produces a bright, even wash with minimal visible dot pattern at typical viewing distances.
• IP68, factory-sealed: Fully sealed for wet cockpit and outdoor exposed locations; suitable for spray zones above water. Do not permanently submerge.
• Dimmable and MFD-upgradeable: Works with a simple momentary switch out of the box; add the EOS-LUX Command Center to control from Garmin, Simrad, B&G, Raymarine, Furuno, or Humminbird MFDs.
• UV-resistant and salt-spray tested: Constructed for the marine outdoor environment; 3M adhesive backing plus optional stainless steel screw clips for extra hold on vertical or overhead runs.
• Authorized dealer support: buy from MyGreenOutdoors with Garmin- and Lumishore-focused product help and fast shipping on qualifying orders.

Key specifications

Compatibility & control

The LUX SL180 requires a Lumishore LUX Strip Light Driver to operate — it cannot be wired directly to a battery or standard LED dimmer. The voltage-stabilised driver (60-0383 / 010-04383-00) accepts 10.5–31 V DC and handles both 12 V and 24 V vessels. For MFD or smart device control, add the EOS-LUX Command Center (60-0366) to enable zone naming, scene programming, and integration with:

• Garmin — Compatible Garmin MFDs via EOS-LUX Command Center
• Simrad / B&G — NSO, NSS EVO, Zeus, and Vulcan series
• Raymarine — Axiom, Axiom Pro, Axiom XL series
• Lowrance — HDS series
• Furuno — NavNet TZtouch series
• Humminbird — Helix and Solix series
• EOS-LUX-SUPRA Display (60-0369) — Optional dedicated Lumishore touchscreen controller

Compare related options

Use these if you need a different length, a field-cuttable version, or a neon-tube profile:

• LUX SL180 — 300mm (010-04364-00) — Shortest run; accent under nav lights or step edges
• LUX SL180 — 600mm (010-04367-00) — Cup-holder channels and short accent runs
• LUX SL180 — 1000mm (010-04371-00) — Standard single-zone run; one meter flat tape
• LUX SL180 — 2500mm (010-04386-00) — Full cockpit seat rail or cabin soffit in one piece
• LUX SL180 — 5000mm (010-04408-00) — Maximum factory-sealed length; large-vessel perimeter
• LUX SL180 Cut & Seal versions — Same strip with a pre-connector allowing a single field cut; supplied with silicone sealing kit
• LUX SNL180 Neon Flex (010-04410-00 series) — Silicone neon-tube profile for curved surfaces and dot-free appearance

Frequently asked questions

Does the SL180 strip light need a driver?
Yes. The SL180 runs at 23–25 V DC and must be powered by a Lumishore LUX Strip Light Driver. The voltage-stabilised driver (60-0383) accepts 10.5–31 V DC input and is compatible with both 12 V and 24 V boats. Do not connect the strip directly to your battery or any third-party driver — this voids the warranty.

Can I cut this strip to a shorter length?
No. This is a standard factory-sealed SL180. Cutting breaks the IP68 seal and voids the warranty. If you need a custom field-cuttable length, order the LUX SL180 Cut & Seal version, which includes a silicone sealing kit and factory-cut connectors at marked intervals.

How many 300 mm strips can I run on one driver?
Each driver handles up to 10 m total strip length. For 300 mm strips that is up to 33 strips per driver (if that is your only load). Combine lengths from multiple strips as long as the total does not exceed 10 m.

Can I bend the SL180 around corners?
The SL180 bends in the vertical axis only (minimum 50 mm radius) — not horizontally. For installations requiring horizontal side-bends around curved surfaces, use the LUX SNL180 Neon Flex, which is specifically designed for side-bending with a 120 mm minimum radius.

Is the LUX SL180 compatible with my Garmin MFD?
With the EOS-LUX Command Center (60-0366) added, yes. The strip light driver connects to the EOS-LUX Command Center, which then interfaces with Garmin MFDs and other major brands. Switch-only operation works without the Command Center.

What's the warranty on the LUX SL180?
Lumishore covers the SL180 with a 3-year warranty. MyGreenOutdoors is a Garmin and Lumishore authorized dealer and can support warranty requests.

Is this suitable for underwater use?
No. The LUX SL180 is rated for above-water indoor and outdoor installation only. Although it is IP68-rated (immersion-tolerant), Lumishore's installation guide specifies it is not designed for permanent submersion. For underwater lighting, see the Lumishore ORA and EOS thru-hull and surface-mount underwater light series.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.